Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Enhancement of oxygen/pressure sensing performance of Eu3+-doped YSZ phosphors via Bi3+ sensitization

The effects of the incorporation of a Bi³⁺ sensitizer on the phosphorescence properties and oxygen partial pressure sensitivity of the Eu³⁺ doped yttria stabilized zirconia (YSZ) phosphors were studied using a lifetime-based optical measurement system. Two series of YSZ: Eu phosphors were investigated in this work: Eu_0.01Bi_xY_0.07-xZr_0.92O_1.96 substitutional series and Eu_0.01Bi_xY_0.07Zr_0.92-xO_1.96-0.5x additive series. The phosphorescence intensity of the additive-series phosphors was enhanced by 47% excited at 405 nm with a Bi³⁺ concentration of 2 mol% due to the energy transfer between Bi³⁺ and Eu³⁺. In contrast, the phosphorescence intensity of the substitutional-series phosphors decreased as the Bi³⁺ concentration increased. The phosphorescence lifetimes for both series phosphors were highly sensitive to oxygen partial pressure at elevated temperatures. With increasing Bi³⁺ concentration, the oxygen sensitivities of both series were enhanced initially, which was related to the increment of concentration dependent non-radiative decay via cross-relaxation between Bi³⁺ and Eu³⁺. With 1 mol% Bi³⁺ doping, the oxygen sensitivity was enhanced by 28% and 12% for substitutional-series and additive-series phosphors, respectively. As the Bi³⁺ concentration further increased, the oxygen sensitivities of both series declined, which was attributed to the energy transfer between Bi³⁺, the formation of Bi³⁺ aggregates as well as the increase of the Eu³⁺ site symmetry. The results of this study not only provided valuable references for phosphor thermometry, but also offered new ideas for developing high-temperature non-contact pressure sensors.     

基于信任链的骚扰电话预判技术研究

当前,骚扰电话乱象屡禁不止,严重影响了人民群众的正常生活,甚至威胁到个人财产安全,因此简单有效地识别骚扰电话技术成为亟待解决的问题。区别于现有的对电话号码进行黑白名单标记、大数据分析等识别方法,提出基于信任链的骚扰电话预判技术,从可信度量的角度计算来电号码的可靠程度,并针对高危受害群体的典型应用场景进行分析,通过对骚扰电话的预判,降低其受到电话骚扰甚至电话诈骗的可能性。     

提升管内颗粒浓度梯度力的特性

由于Kutta-Joukowski横向力与浓度梯度力的共同作用，提升管内颗粒沿径向在边壁大量聚集并形成稳定的环?核结构。根据实验数据，分析了颗粒浓度梯度的径向分布特征，考察了不同操作条件下浓度梯度力系数K的分布特性。由Kutta-Joukowski横向力与浓度梯度的关系，提出了浓度梯度力的表达式Fρ=K(dρ/dr)A及浓度梯度力系数K的表达式K=[?ρg(νg?νp)(?v/?r)r]/?dρ/dr+(d2ρ/dr2)r?。提升管内颗粒群受到的浓度梯度力与浓度梯度力系数K有关。浓度梯度力系数K在提升管中心处为0，沿提升管径向呈“N”型分布，随表观气速增加而增加；提升管内充分发展段K的数值明显大于提升管加速区和出口约束区，总结了浓度梯度力系数K的经验关联式。     

镁合金网格壁板压弯成形数值模拟及实验研究

为探索镁合金整体壁板压弯成形的可行性,以及镁合金壁板压弯成形过程中金属的流动规律,对AZ31镁合金网格壁板压弯成形进行了数值模拟和实验研究。建立了有限元数值模拟的几何模型,采用有限元计算软件对AZ31镁合金网格壁板压弯成形过程进行了数值模拟研究,分析了镁合金网格壁板压弯成形中的温度场、应变场、应力场、破坏系数等的分布规律。确定了合适的AZ31镁合金壁板压弯成形工艺参数,并对镁合金网格壁板压弯成形进行了实验研究,获得了合格的镁合金网格壁板弯曲件,并分析了镁合金网格壁板成形件尺寸精度,模拟结果与实验结果相吻合,最大相对误差为16.7%。     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

Analysis and assessment of a nanoparticle seeded small scale absorption refrigeration system driven by a low‐grade waste heat source

The thermoeconomic behaviour of a nanoparticle seeded single effect LiBr‐H₂O absorption refrigeration system (ARS) is investigated for a small scale application. In the proposed method, alumina nanoparticles with volume concentrations of 3%, 5%, and 7% are dispersed into an aqua lithium bromide solution. The multiobjective heat transfer search algorithm is employed to examine the design trade‐off between the coefficient of performance (COP) and total annualized cost (TAC). To analyze the overall performance of the system, the influence of five design parameters, namely the temperatures of the generator, absorber, evaporator, condenser and heat exchanger pipe diameter, are studied. It is found that with an increase in the COP, the TAC of the system is initially raised marginally, and after that, raised rigorously with further increment. The comparative results indicate that the COP and TAC of the nanofluid based ARS system are increased by about 7% and decreased by about 3.2%, respectively, corresponding to the Pareto points of the base ARS system. A lower break‐even point of about 2.6 years is achieved for the ARS system containing nanoparticles compared to the base ARS system. Overall, the ARS system containing 5% nanoparticles is the best solution from a thermodynamic and economic point of view.     

Multicolour tunable luminescence of thermal-stable Ce3+/Tb3+/Eu3+-triactivated Ca3Gd(GaO)3(BO3)4 phosphors via Ce3+ → Tb3+ → Eu3+ energy transfer for near-UV WLEDs applications

A series of single-component blue, green and red phosphors have been fabricated based on the Ca₃Gd(GaO)₃(BO₃)₄ host through doping of the Ce³⁺/Tb³⁺/Eu³⁺ ions, and their crystal structure and photoluminescence properties have been discussed in detail. A terbium bridge model via Ce³⁺ → Tb³⁺ → Eu³⁺ energy transfer has been studied. The emission colours of the phosphors can be tuned from blue (0.1661, 0.0686) to green (0.3263, 0.4791) and eventually to red (0.5284, 0.4040) under a single 344 nm UV excitation as the result of the Ce³⁺ → Tb³⁺ → Eu³⁺ energy transfer. The energy transfer mechanisms of Ce³⁺ → Tb³⁺ and Tb³⁺ → Eu³⁺ were found to be dipole-dipole interactions. Importantly, Ca₃Gd(GaO)₃(BO₃)_4:Ce³⁺,Tb³⁺,Eu³⁺ phosphors had high internal quantum efficiency. Moreover, the study on the temperature-dependent emission spectra revealed that the Ca₃Gd(GaO)₃(BO₃)_4:Ce³⁺,Tb³⁺,Eu³⁺ phosphors possessed good thermal stability. The above results indicate that the phosphors can be applied into white light-emitting diodes as single-component multi-colour phosphors.